Reference [Recorder]
key to begin recorder playback. 
3.
Locate the point at which you want to punch in, 
and press the [AUTO PUNCH IN/OUT] key. 
5.
When you come to the punch in point, press the 
The [AUTO PUNCH IN/OUT] key flashes. This sets the  In 
REC [O] key (or press the foot switch). 
point  at which recording will begin. 
The REC [
O
] key lights up, and track recording begins from 
that location. 
4.
Locate the point at which you want to punch out, 
and press the [AUTO PUNCH IN/OUT] button once 
6.
When you come to the intended punch out point, 
more. 
press the REC [O] key (or the foot switch) once 
This sets the  Out point  at which recording will end. The 
again. 
[AUTO PUNCH IN/OUT] button will change from flashing 
The REC [
O
] key goes out, and the unit switches from 
to solidly lit. This indicates that the auto punch in/out 
recording to playback. 
function is now enabled. 
7.
To stop playback, press the STOP [P] key. 
H
INT
If you want to specify the in/out points precisely, it is 
8.
To check the newly recorded content, locate to a 
convenient to use the scrub function (
  
p. 44) to find the 
locations and assign a mark (
  
p. 42) beforehand at the 
point slightly before the punch in point, and press 
desired locations. 
the PLAY [R] key. 
5.
Use the Locate function to go to a spot slightly 
before the In point. 
Using auto punch in/out 
6.
Repeatedly press the status key for the track on 
Auto punch in/out is a function that lets you specify 
which you want to perform punch in/out, until the 
beforehand the region to be re recorded. Punch in will occur 
key flashes red. 
automatically when you reach the starting location (In 
point), and punch out will occur automatically when you 
reach the ending location (Out point). This is convenient for 
N
OTE
example when you cannot operate the MRS 802 because 
A status key that is lit red means that the current location is 
you are playing the instrument yourself, or when very fast 
between the In point and Out point. In this case, operate the 
playback/record switching is required. 
transport once again to locate to a point that is earlier than 
the In point. 
In point
Out point 
7.
If you want to rehearse the auto punch in/out, 
Track Playback Playback 
Recording 
press the PLAY [R]key. 
The recorder will begin playing. When you reach the In 
In order to perform auto punch in/out, you must first specify 
point, the track on which you are punching in/out will be 
the In point (switch point from playback to recording) and 
muted. When you reach the Out point, muting will be 
Out point (switch point from recording to playback), and 
defeated. (You will always be able to monitor the input 
then perform the recording operation. The procedure is as 
signal during this time.) Performing this action will not 
follows. 
delete or record anything on the track. 
1.
Raise the fader of the track where you want to 
When you are finished rehearsing, move again to a location 
perform auto punch in/out to a suitable position. 
earlier than the In point. If necessary, adjust the In/Out 
points. 
2.
While playing the instrument connected to the 
8.
input jack, use the [INPUT] control and [REC 
To actually perform auto punch in/out, hold down 
LEVEL] control to adjust the recording level. 
the REC [O] key and press the PLAY [R] key. 
The recorder operates in playback mode. When you reach 
ZOOM MRS 802
36






footer




 

 

 

 

 Home | About Us | Network | Services | Support | FAQ | Control Panel | Order Online | Sitemap | Contact

ireland web hosting

 

Our partners: PHP: Hypertext Preprocessor Cheap Web Hosting JSP Web Hosting Ontario Web Hosting  Jsp Web Hosting

Cheapest Web Hosting Java Hosting Cheapest Hosting

Visionwebhosting.net Business web hosting division of Vision Web Hosting Inc.. All rights reserved